!   TITLE:  ms.parm
!
!---------------------------------------------------------------------------
!       Rev -   RELEASED    07/24/2001      J. Rinaldi
!---------------------------------------------------------------------------
!
!   This is the parameter file used in the construction of the CRES 410
!   mirror support, 'mirror_support.mac', SK400A007.
!
!
!---------------------- a.) Title and Units Declaration --------------------
!
ms_mtrl='al6061'
/title,AAAV Mirror Support Construction / SK400A007 / %ms_mtrl%
!
/units,bin                      ! British/inch units
!
!--------------------- b.) Part Name Selection Variable --------------------
!
name='mir_supt'
arry_nam='mirsp'
!
!--------------------------- c.) Model C.S. Names --------------------------
!
ct_name='CSmirsp0'                      ! cartesian
cyl_name='CSmirsp1'                     ! cylindrical
sph_name='CSmirsp2'                     ! spherical
!
!----------------------- d.) Material and Element Type ---------------------
!
mat_select,ms_mtrl
!
et,1,shell93                            ! Element Types
et,2,solid95
et,3,solid92
!
!--------------------------- e.) Model Parameters --------------------------
!
el_up=31
el_down=11


thick=.15                   ! Typical wall thickness
thickc=.10                  ! Center rib wall thickness
rfil=.060
rfil2=.250

CSz1=-.25   !-.1                    ! Location of Datum -H-

l1=7.125-2.336              !----- See figure 1. -----
l2=2.336+2.450
l3=1.45         !1.004
l4=1.45         !1.006
h1=1.975        ! 3.800/2
h2=h1
!
phi1=10
*afun,deg
h13=h1-(l2-l4)*tan(phi1)    ! Vertex of angled line at torquer end
h14=1.18590825              ! Vertex of pocket line at torquer end
h15=1.73005331
*afun,rad
!
Dro=1.5
Dri=Dro-thick
!
h16=1.10        ! Width of torquer end base


!
h3=1.280                    !----- See figure 2. -----
h4=0.755        !was .780
phi2=9
dlj=2.150
drj=1.070
d1=0.9839
d2=0.755
d3=0.8536
d4=0.4990
extd1=dlj
!
ribw=0.200                  !----- See figure 3. -----  ! 0.200
lrext=4.336
llext=4.364
!l5=lrext
l5=2.336+2.45-thick
l6=3.636
l7=l6-ribw
l8=2.736
l9=l8-ribw
l10=1.8     !1.55   ! 1.836
l10t=2.125  !1.77   ! Torquer side
h5=thick    ! 0.360
h5a=thick   ! Resolver side wall
h6=.050     ! 0.200
h6a=.050    ! .350/2    ! Opposite from mirror
h7=.250     ! .755      ! .15       ! 0.420  ! Thickness at pocket bottoms
h7a=.655    !.7
phi3=0      ! 5
!
l11=1.000   !0.800                  !----- See figure 4. -----
l12=1.000   !1.200
h8=0.625
h9=3.220
phi4=60
dcut=0.220
!
l13=0.825                   !----- See figure 5. -----
l14=2.975
h10=0.120
chmf1=0.225
chmf2=0.100
phi5=30
!
l15=2.614                   !----- See figure 6. -----
l16=1.300
rrad=0.250
!
dos=2.000
dhole=1.95          ! was 1.025
dbore1=2.5          ! was 1.754
dbore2=dos-.2       ! 1.612     ! use in:    elev_reslvr_adaptor.mac
h11=0.909           ! was .935
h12=0.585
l17=0.324           ! was .439
!
boredpth=h11-l17
extd2=5.366-l1
extd3=0.322
extd4=0.532
!
l18=0.340
l19=.054
l20=0.789-l18-l19
l21=1.465-0.789
l22=5.044
!
l23=0.3220125
l24=0.3170125
l25=10.008
!
extd5=l25-l22-l2
!
xcenter=2.336               ! X distance from -Z- to center hole
xbandj=7.125                ! X distance from -Z- to cast band journal
tside=-xbandj+xcenter+l22+extd3-extd4 ! Thickness of flange by the band journal
!
! Hole pattern on the back - added to allow balancing of elev axis
hdia=.688
hdepth=.190
*dim,xh,array,3
xh(1)=2.5
xh(2)=3.5
xh(3)=4.375
yh=.50
!
! Additional cut on back to clear increased size gimbal with the larger
! torquer stator
!
width1=L3+L4    ! 2.8       ! 3.000
depth1=.295
ycut=h2         !.096
rcut=.125
cham1=.250
!
!-------------- 3.1.2 Center Cut of Gimbal Center Hub Clearance -----------
!
! Prefix hc = Hub Clearance
xoffax=.160 !.1585  ! X offset of (w.r.t CStprof) of MS bore axis to Az axis

hcDx1=1.75  !1.3    ! 1/2 the width of clearance cut at bottom
hcDx2=.90           ! Width of extrude at tapered end
hcDa1=45
hcDy1=.614      ! Cut depth w.r.t. to elev axis
hcDy2=h11-hcDy1 ! Cut depth w.r.t. CStprof

hcDz1=h1+h2-thick   ! 2.70      ! Depth of extrude from edge of MS

! Straight cut instead of 45 degree sides
hcDx1=hcDx1+.1
!hcDx2=hcDx2        ! +.1


!
!---------------------- 3.6.3 Center cut (extrude) ------------------------
!
ccDr1=1.1250
ccDr2=0.060
!
ccPx1=1.300000
ccPy3=1.750000
!
ccDext=0.435

!------------- 3.6.3 Angled Rib Center Cut Version (extrude) --------------
c1Dr1=1.1250                 ! Used for lm + 2
c1Dr2=0.12500                ! Used for lm + 4
c1Dr3=c1Dr2                  ! Used for lm + 5
c1Dr4=c1Dr2                  ! Used for lm + 7
c1Dr5=c1Dr2                  ! Used for lm + 8
!
c1Px1=-0.9740993
c1Py1=1.750000
c1Pz1=0.000000

c1Px2=0.9740982
c1Py2=c1Py1
c1Pz2=c1Pz1

c1Px3=0.5245652
c1Py3=0.9952167
c1Pz3=c1Pz1

c1Px4=-0.5245640
c1Py4=0.9952174
c1Pz4=c1Pz1

c1Px5=0.000000
c1Py5=0.6661338E-15
c1Pz5=c1Pz1

c1Px6=0.6826796
c1Py6=1.030570
c1Pz6=c1Pz1

c1Px7=1.073928
c1Py7=1.549773
c1Pz7=c1Pz1

c1Px8=c1Px2
c1Py8=1.625000
c1Pz8=c1Pz1

c1Px9=0.5828502
c1Py9=1.105796
c1Pz9=c1Pz1

c1Px10=-0.6826796
c1Py10=c1Py6
c1Pz10=c1Pz1

c1Px11=-1.073928
c1Py11=c1Py7
c1Pz11=c1Pz1

c1Px12=-0.9740982
c1Py12=c1Py8
c1Pz12=c1Pz1

c1Px13=-0.5828502
c1Py13=c1Py9
c1Pz13=c1Pz1
!------------- 3.6.3 2nd Angled Rib Center Cut Version (extrude) ----------
c2Dr1=1.1250                 ! Used for lm + 2
c2Dr2=0.12500                ! Used for lm + 3
c2Dr3=c2Dr2                  ! Used for lm + 5
c2Dr4=c2Dr2                  ! Used for lm + 6
!
c2Px1=1.300000
c2Py1=0.4264681
c2Pz1=0.000000

c2Px2=c2Px1
c2Py2=1.226950
c2Pz2=c2Pz1

c2Px3=1.057500
c2Py3=0.3838212
c2Pz3=c2Pz1

c2Px4=0.8120740
c2Py4=0.7785633
c2Pz4=c2Pz1

c2Px5=0.1998401E-14
c2Py5=0.1221245E-14
c2Pz5=c2Pz1

c2Px6=1.175000
c2Py6=c2Py1
c2Pz6=c2Pz1

c2Px7=0.8024750
c2Py7=0.9402972
c2Pz7=c2Pz1

c2Px8=1.075171
c2Py8=1.302177
c2Pz8=c2Pz1

c2Px9=0.9023044
c2Py9=0.8650704
c2Pz9=c2Pz1

c2Px10=c2Px6
c2Py10=c2Py2
c2Pz10=c2Pz1
!
!----------------- 3.3  Create Rib Pockets --------------------------------
po2Dr1=0.25000               ! Used for lm + 3
po2Dr2=po2Dr1                ! Used for lm + 7
po2Dr3=po2Dr1                ! Used for lm + 11
po2Dr4=po2Dr1                ! Used for lm + 14
po2Dr5=po2Dr1                ! Used for lm + 15
po2Dr6=po2Dr1                ! Used for lm + 16
po2Dr7=1.3500                ! Used for lm + 18
po2Dr8=po2Dr1                ! Used for lm + 19
po2Dr9=po2Dr1                ! Used for lm + 20
po2Dr10=po2Dr1               ! Used for lm + 22
po2Dr11=po2Dr7               ! Used for lm + 23
po2Dr12=po2Dr1               ! Used for lm + 24
po2Dr13=po2Dr1               ! Used for lm + 27
po2Dr14=po2Dr1               ! Used for lm + 28
po2Dr15=po2Dr1               ! Used for lm + 29
po2Dr16=po2Dr1               ! Used for lm + 30

!
! Keypoint Parameter Definitions
!

po2Dr1=1.2000                ! Used for lm + 4
po2Dr2=0.25000               ! Used for lm + 6
po2Dr3=po2Dr1                ! Used for lm + 8
po2Dr4=po2Dr2                ! Used for lm + 11
po2Dr5=po2Dr2                ! Used for lm + 12
po2Dr6=po2Dr2                ! Used for lm + 13
po2Dr7=po2Dr2                ! Used for lm + 14
po2Dr8=po2Dr2                ! Used for lm + 15
po2Dr9=po2Dr2                ! Used for lm + 21
po2Dr10=po2Dr2               ! Used for lm + 22
po2Dr11=po2Dr2               ! Used for lm + 23
po2Dr12=po2Dr2               ! Used for lm + 24
po2Dr13=0.50000              ! Used for lm + 26
po2Dr14=po2Dr13              ! Used for lm + 27
po2Dr15=po2Dr13              ! Used for lm + 28
po2Dr16=po2Dr13              ! Used for lm + 29

!
! Keypoint Parameter Definitions
!

po2Px1=-4.639000
po2Py1=0.4000000
po2Pz1=2*extd1      ! 0.000000

po2Px2=po2Px1
po2Py2=0.8982904
po2Pz2=po2Pz1

po2Px3=po2Px1
po2Py3=-0.4000000
po2Pz3=po2Pz1

po2Px4=po2Px1
po2Py4=-0.8982904
po2Pz4=po2Pz1

po2Px5=2.439033
po2Py5=-1.495979
po2Pz5=po2Pz1

po2Px6=3.494372
po2Py6=-1.309894
po2Pz6=po2Pz1

po2Px7=4.435809
po2Py7=-0.4715464
po2Pz7=po2Pz1

po2Px8=3.286000
po2Py8=-0.1281237
po2Pz8=po2Pz1

po2Px9=1.940641
po2Py9=-0.4606339
po2Pz9=po2Pz1

po2Px10=2.153086
po2Py10=-1.310411
po2Pz10=po2Pz1

po2Px11=2.395621
po2Py11=-1.249777
po2Pz11=po2Pz1

po2Px12=2.578157
po2Py12=0.5767767
po2Pz12=po2Pz1

po2Px13=3.246334
po2Py13=1.244954
po2Pz13=po2Pz1

po2Px14=po2Px7
po2Py14=0.4715464
po2Pz14=po2Pz1

po2Px15=3.459193
po2Py15=1.315560
po2Pz15=po2Pz1

po2Px16=po2Px8
po2Py16=0.1281237
po2Pz16=po2Pz1

po2Px17=2.754934
po2Py17=0.1500000
po2Pz17=po2Pz1

po2Px18=4.196266
po2Py18=po2Py17
po2Pz18=po2Pz1

po2Px19=2.183177
po2Py19=-0.1500000
po2Pz19=po2Pz1

po2Px20=po2Px18
po2Py20=po2Py19
po2Pz20=po2Pz1

po2Px21=po2Px18
po2Py21=po2Py1
po2Pz21=po2Pz1

po2Px22=3.423111
po2Py22=1.068177
po2Pz22=po2Pz1

po2Px23=po2Px17
po2Py23=po2Py1
po2Pz23=po2Pz1

po2Px24=po2Px19
po2Py24=po2Py3
po2Pz24=po2Pz1

po2Px25=po2Px18
po2Py25=po2Py3
po2Pz25=po2Pz1

po2Px26=-4.389000
po2Py26=po2Py19
po2Pz26=po2Pz1

po2Px27=-2.183371
po2Py27=po2Py19
po2Pz27=po2Pz1

po2Px28=po2Px26
po2Py28=po2Py17
po2Pz28=po2Pz1

po2Px29=-1.858371
po2Py29=po2Py17
po2Pz29=po2Pz1

po2Px30=-4.432412
po2Py30=1.144492
po2Pz30=po2Pz1

po2Px31=-1.829952
po2Py31=1.603376
po2Pz31=po2Pz1

po2Px32=po2Px30
po2Py32=-1.144492
po2Pz32=po2Pz1

po2Px33=-2.361985
po2Py33=-1.509564
po2Pz33=po2Pz1

po2Px34=-1.698300
po2Py34=-0.7712678
po2Pz34=po2Pz1

po2Px35=-1.790090
po2Py35=-1.138428
po2Pz35=po2Pz1

po2Px36=po2Px26
po2Py36=po2Py4
po2Pz36=po2Pz1

po2Px37=po2Px26
po2Py37=po2Py3
po2Pz37=po2Pz1

po2Px38=po2Px26
po2Py38=po2Py1
po2Pz38=po2Pz1

po2Px39=po2Px26
po2Py39=po2Py2
po2Pz39=po2Pz1

po2Px40=-1.258057
po2Py40=0.9897045
po2Pz40=po2Pz1

po2Px41=-1.373300
po2Py41=0.5287322
po2Pz41=po2Pz1

po2Px42=-1.743128
po2Py42=1.110972
po2Pz42=po2Pz1

po2Px43=po2Px29
po2Py43=0.6500000
po2Pz43=po2Pz1

po2Px44=-2.275161
po2Py44=-1.017161
po2Pz44=po2Pz1

po2Px45=po2Px27
po2Py45=-0.6500000
po2Pz45=po2Pz1

!
!--------------- 3.6.3  Center pockets on back (extrude) ------------------
!
po3Dr1=1.1250                ! Used for lm + 1
po3Dr2=po3Dr1                ! Used for lm + 2
po3Dr3=po3Dr1                ! Used for lm + 3
po3Dr4=0.25000               ! Used for lm + 6
po3Dr5=po3Dr4                ! Used for lm + 8
po3Dr6=po3Dr4                ! Used for lm + 9
po3Dr7=po3Dr4                ! Used for lm + 10
po3Dr8=po3Dr4                ! Used for lm + 13
po3Dr9=po3Dr4                ! Used for lm + 16
po3Dr10=po3Dr1               ! Used for lm + 17
po3Dr11=po3Dr4               ! Used for lm + 18
po3Dr12=po3Dr4               ! Used for lm + 19
po3Dr13=po3Dr4               ! Used for lm + 20
po3Dr14=po3Dr4               ! Used for lm + 22
po3Dr15=po3Dr4               ! Used for lm + 23

!
! Keypoint Parameter Definitions
!

po3Px1=0.8089830
po3Py1=0.7817745
po3Pz1=0.000000

po3Px2=-0.4893607
po3Py2=1.012991
po3Pz2=po3Pz1

po3Px3=-0.2220446E-15
po3Py3=-0.1110223E-15
po3Pz3=po3Pz1

po3Px4=1.007510
po3Py4=-0.5005485
po3Pz4=po3Pz1

po3Px5=1.081702
po3Py5=-0.3091032
po3Pz5=po3Pz1

po3Px6=-0.3787890
po3Py6=-1.059313
po3Pz6=po3Pz1

po3Px7=0.000000
po3Py7=-1.125000
po3Pz7=po3Pz1

po3Px8=-0.5213826
po3Py8=1.795000
po3Pz8=po3Pz1

po3Px9=0.8413826
po3Py9=po3Py8
po3Pz9=po3Pz1

po3Px10=-0.7639182
po3Py10=1.605634
po3Pz10=po3Pz1

po3Px11=-0.8406432
po3Py11=1.298734
po3Pz11=po3Pz1

po3Px12=-0.5981075
po3Py12=1.238100
po3Pz12=po3Pz1

po3Px13=1.083918
po3Py13=po3Py10
po3Pz13=po3Pz1

po3Px14=1.231293
po3Py14=1.016136
po3Pz14=po3Pz1

po3Px15=po3Px9
po3Py15=1.545000
po3Pz15=po3Pz1

po3Px16=po3Px8
po3Py16=po3Py15
po3Pz16=po3Pz1

po3Px17=0.9887571
po3Py17=0.9555022
po3Pz17=po3Pz1

po3Px18=-0.7432486
po3Py18=-1.825000
po3Pz18=po3Pz1

po3Px19=1.275381
po3Py19=po3Py18
po3Pz19=po3Pz1

po3Px20=1.564616
po3Py20=-0.3171589
po3Pz20=po3Pz1

po3Px21=1.672839
po3Py21=-0.7500504
po3Pz21=po3Pz1

po3Px22=1.322081
po3Py22=-0.3777928
po3Pz22=po3Pz1

po3Px23=1.253527
po3Py23=-0.9874610
po3Pz23=po3Pz1

po3Px24=1.054624
po3Py24=-0.7885582
po3Pz24=po3Pz1

po3Px25=1.452157
po3Py25=-1.398223
po3Pz25=po3Pz1

po3Px26=0.9876280
po3Py26=-0.9336940
po3Pz26=po3Pz1

po3Px27=po3Px19
po3Py27=-1.575000
po3Pz27=po3Pz1

po3Px28=0.6634238
po3Py28=-0.9085669
po3Pz28=po3Pz1

po3Px29=1.231401
po3Py29=-0.6117816
po3Pz29=po3Pz1

po3Px30=0.8108513
po3Py30=-1.110471
po3Pz30=po3Pz1

po3Px31=1.430304
po3Py31=-0.8106843
po3Pz31=po3Pz1

po3Px32=-0.9200253
po3Py32=po3Py25
po3Pz32=po3Pz1

po3Px33=-0.6397411
po3Py33=-1.117939
po3Pz33=po3Pz1

po3Px34=-0.4629644
po3Py34=-1.294716
po3Pz34=po3Pz1

po3Px35=po3Px18
po3Py35=po3Py27
po3Pz35=po3Pz1

!
!----------------- 3.8 Hole Pattern for Adapter ---------------------------
!
hpDr1=2.250/2       ! Hole pattern radius
hpDd1=.218          ! C'bore dia
hpDd2=.125          ! Clearance hole dia
hpDz1=.120          ! Section B-B thickness from SK400A007 SH2
!
!----------------- 3.9 Lightnening Holes -------------------------
!
nlh=12
*dim,CSlhx,array,nlh
*dim,CSlhy,array,nlh
*dim,lhDr1,array,nlh

! Torquer Side Holes
CSlhx(1)= 2.025, 2.690, 3.520, 3.815
CSlhy(1)= 1.100,-0.765, 0.715,-0.630
lhDr1(1)= 0.500, 0.500, 0.375, 0.375

! Center Section Holes
CSlhx(5)= 1.240,-1.020
CSlhy(5)=-1.375,-1.450
lhDr1(5)= 0.250, 0.250

! No side holes version (center section holes only)
!CSlhx(1)=0.785, 0.895, 1.405,-0.460,-0.575,-1.155
!CSlhy(1)=1.500,-1.490,-0.765, 1.500,-1.490,-1.115
!lhDr1(1)=0.250, 0.250, 0.250, 0.250, 0.250, 0.250


! Resolver Side Hole
CSlhx(7)=-2.020,-2.390,-3.195,-3.430,-4.120,-4.220
CSlhy(7)= 0.855,-0.820, 0.750,-0.730, 0.670,-0.660
lhDr1(7)= 0.500, 0.500, 0.375, 0.375, 0.250, 0.250
!
!----------------- 3.10 Back Cut For Balancing ----------------------------
!
h17=0.400           ! Depth of corner on resolver end
h18=0.350           ! Depth of corner on torquer end
h19=-CSz1           ! Depth at X distance L27
l27=2.900
!
!----------------- 3.11 Resolver End Lightnening Holes -------------------------
!
nlhr=2
*dim,CSlhrx,array,nlhr      ! lhr = Lightening Hole Resolver
*dim,CSlhry,array,nlhr
*dim,lhrDr1,array,nlhr
!
CSlhrx(1)=-0.530,-0.530
CSlhry(1)= 0.415,-0.415
lhrDr1(1)= 0.250, 0.250

extd6=1.000
!
!----------------------------- Temperatures  ------------------------------
!
Troom=70                ! [deg F] Room temp (zero thermal stress)
Ttest=-40               ! [deg F] Test temp
!
!------------------------ f.) Model C.S. Coordinates -----------------------
!
acs=CSra0                       ! active coordinate system
!
xc=0                            ! x coordinate center
yc=h11                          ! y coordinate center
zc=-L22                         ! z coordinate center
!
rotxyc=90  ! -90                ! z axis (xy rotation)
rotyzc=180 ! 0                  ! x axis (yz rotation)
rotzxc=-90 ! 90                 ! y axis (zx rotation)
!
!---------------------------------------------------------------------------